Mk-diamond MK-370 Instrukcja Użytkownika

05.2010MK-370 TILE SAWOWNERS MANUALPARTS LIST &OPERATING INSTRUCTIONSwww.mkdiamond.comCaution: Read all safety and operating instructions before u

10MK-370 SAW SAFETYUse of under sized extension cords

11SAFETY LABEL LOCATIONSSafety labels contain important safety information. Please read the information contained on each safety label. These labels a

12PRODUCT SPECIFICATIONSThe MK-370 is a versatile Tile Saw. Operated and used according to this manual, the MK-370 will provide years of dependable se

13D7C;7::H;II9?JOIJ7J; P?F9E:;F>ED; <7N;#C7?BFHE:K9JCE:;BF7HJDKC8;HC79>?D;I;H?7BB@9>6BDC9L6GG6CIN86G9qJ?B;:?IJH?8KJEH q>EC;

14MK-370 SAW INSTALLATION(D)Align the Cutting Head Retaining Hole

15MK-370 SAW INSTALLATION When installing the Retaining Screw, do

16(B)Install the Thumbscrewthrough the Washer and Splashguard then align to the hole found on back of the Blade Guard and tightenMK-370 SAW

17WATER PUMP PREPARATION(B)Connect the Cooling Transfer Tube to the inlet connection of the Blade Guard(A)Press the end of the cooling Transfer Tube o

18SETUP FOR OPERATION1. Before connecting the MK-370 Saw to a power supply, be sure the voltage, cycle and phase meet the requirements of table be

19MK-370 SAW OPERATIONADJUSTMENT & OPERATIONDO NOT FORCE

2INTRODUCTION Congratulations on your purchase of a MK-370 Saw. We are certain that you will be pleased with your purchase. MK Diamond takes pride

20(D)Fill the Water Pan with clean water(B)Dispose of the contents of the Water Pan and clean the pan. Replace the Cutting Assembly.(A)Ensure the ON/O

21(K)Lubricate the Roller Wheel Assembly(J)Lubricate the Guide BarTo extend the life of the MK-370 Saw, the following procedure should be performed af

22MK-370 SAW MAINTENANCE(D)Verify the Movable Cutting Table Roller

23MK-370 SAW MAINTENANCEMOTOR BRUSH CHANGE-OUTDisconnect the tool

24MK-370 SAW TROUBLESHOOTINGTROUBLESHOOTINGBlade will not cut properly.(A)Ch

25"Rodding" cooling channels is performed by inserting a small wire rod through the cooling inlet on top of the Blade Guard and directing th

26MK-370 SAW TROUBLESHOOTINGBLADE STOPS TURNING(A)Check the ON/OFF Switch is

27NOTES

28MK-370 SAW EXPLODED VIEW

29MK-370 SAW PARTS LISTITEM DESCRIPTION PART # QTY A Acc

3TABLE OF CONTENTS SAFETYSafety Messages 4 Damage Prevention Message 4 General Safety Precautions 4 Rules for Safe Operation 4California Proposit

30MK-370 SAW PARTS LISTITEM DESCRIPTION PART # QTY H9

31MK-370 SAW EXPLODED VIEWRyobi Motor

32ITEM DESCRIPTION PART # QTY 1 GEAR SHAFT 6110298 1 2 PARALLEL KEY 5X5X14 6100224 1 3 GEAR CASE COVER 6821489 1 4 FLAT TAPPING SCREW (S)

33MK-370 SAW THEORYTHEORY OF DIAMOND BLADESDiamond bla

34MK-370 SAW ACCESSORIESITEM 1. MK-200, 10" x 5/8 Arbo

35MK-370 SAW ORDERING & RETURNORDERING INFORMATIONYou may order MK Diamond

MK-370 TILE SAWOWNERS MANUAL & OPERATING INSTRUCTIONS MK Diamond Products, Inc.1315 Storm ParkwayTorrance, CA 90501Toll-Free: (800) 421-5830Phone

4Read and follow all safety, operating and maintenance instructions. Failure to read and follow these instructions could result in injury or death to

5MK-370 SAW SAFETYIf using an extension cord make sure

6MK-370 SAW SAFETYConsult the owner’s manual for recom

7MK-370 SAW SAFETYSawing and drilling generates dust.

8ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONSIn order to prevent potential electrical shock and injury, the following electrical safety precauti

9 Supporting Surface Power Tool Drip Loop Power Cord Drip Loop InformationTo avoid the possibility of the appliance plug or receptacl